Timeline for How can I trim plywood flush to an edge that is not 90 degrees?
Current License: CC BY-SA 4.0
20 events
| when toggle format | what | by | license | comment | |
|---|---|---|---|---|---|
| Feb 24, 2022 at 19:43 | history | edited | aquaticapetheory | CC BY-SA 4.0 |
added what i ended up doing
|
| Feb 24, 2022 at 19:30 | vote | accept | aquaticapetheory | ||
| Feb 23, 2022 at 14:53 | comment | added | gnicko | Does this help: woodworking.stackexchange.com/q/13617/5522? | |
| S Feb 11, 2022 at 13:06 | history | suggested | Peter Mortensen | CC BY-SA 4.0 |
Fixed the question formation - missing auxiliary (or helping) verb - see e.g. <https://www.youtube.com/watch?v=t4yWEt0OSpg&t=1m49s> (see also <https://www.youtube.com/watch?v=kS5NfSzXfrI> (QUASM)) - alternatively, drop the question mark.
|
| Feb 10, 2022 at 2:02 | answer | added | BushMechanic | timeline score: 3 | |
| Feb 10, 2022 at 1:06 | answer | added | Jacob D | timeline score: 4 | |
| Feb 9, 2022 at 19:41 | comment | added | Graphus | Ah sorry, I assumed there wouldn't be room if using a bottom-bearing bit (as you'd want to run the bearing too low down). But with a top-bearing bit the other skin has to not be there yet otherwise the bearing would be riding against that instead of the frame. | |
| Feb 9, 2022 at 18:17 | answer | added | Caleb | timeline score: 2 | |
| Feb 9, 2022 at 17:51 | review | Suggested edits | |||
| S Feb 11, 2022 at 13:06 | |||||
| Feb 9, 2022 at 17:23 | comment | added | aquaticapetheory | @Graphus Yes, plan to trim the plywood on short edges with a flush trim router bit. It's not readily obvious to me, why do I need to do it with only one plywood skin attached? There is room for the bit's bearing to ride on the wooden frame between the sheets. | |
| Feb 9, 2022 at 17:20 | comment | added | aquaticapetheory | @Max I could still do it with a circular saw and a cutting guide but it would be tricky. There are nails in the long edges and I don't want to make it any narrower so I would just leave a little plywood and sand it down. | |
| Feb 9, 2022 at 16:09 | comment | added | Graphus | I presume you're intending to trim the ply on the short edges using a pattern bit or flush-trim bit yes? In either case, just to mention something in case it isn't obvious: you'd need to fix one plywood skin at a time for this to work. | |
| Feb 9, 2022 at 16:06 | comment | added | Graphus | Creating a bevel angle like this with a circular saw seems sketchy to me, far too easy to make a minor error that could lead to damaging or even writing off what is essentially a finished door at that point. The standard way of creating such a relief angle in a cupboard door (normal for this to be on one long side by the way) used to be by hand planing it, and that could still easily be the method of choice in a power-tool centred workshop — no setup time, just grab the plane, clamp the door and start work. The surface quality will regularly be better too, which could be a further plus. | |
| Feb 9, 2022 at 14:58 | comment | added | Max | Can't you still do the circular saw thing? Angle at 3 degrees and take multiple passes until the blade touches but doesn't cut the frame. Or am i missing something here? | |
| Feb 9, 2022 at 14:54 | answer | added | Max | timeline score: 2 | |
| Feb 9, 2022 at 13:32 | history | became hot network question | |||
| Feb 9, 2022 at 12:51 | answer | added | FreeMan | timeline score: 6 | |
| Feb 9, 2022 at 6:26 | answer | added | Volfram K | timeline score: 9 | |
| S Feb 9, 2022 at 2:08 | review | First questions | |||
| Feb 9, 2022 at 3:38 | |||||
| S Feb 9, 2022 at 2:08 | history | asked | aquaticapetheory | CC BY-SA 4.0 |