10 votes
Accepted

Panel Glue up Question

In general, panel glue-up requires accurate square faces on the boards being glued. However, not all is lost. One possibility is that your combination square is not perfectly square. To try and ...
Eli Iser's user avatar
  • 3,375
7 votes

Using thick branches to make an end-grain cutting board?

I've read about branches having internal stresses and twisting/warping. The main reason not to use wood from branches normally is that it's full of reaction wood, wood that has internal stress from ...
Graphus's user avatar
  • 63.5k
5 votes

Strength of board from squared branches as opposed to trunk wood

In basic outline there's no real problem with what you want to do, after all these days many panels are made in somewhat this way, except that the wood is from branches. Branch wood, unlike the ...
Graphus's user avatar
  • 63.5k
5 votes
Accepted

How much extra thickness should I leave when rough milling green boards?

If you've got a lot to spare, then overdo it. Curves, twists, warps etc will always kill your yield. Flatsawn is apt to be less stable (esp with respect to cupping) than quartersawn. The milling ...
Aloysius Defenestrate's user avatar
4 votes
Accepted

Should I “un-dry” wood for a while after oven drying?

My question is: After I do this but before I plane the boards, should I leave them sit out in the open air (maybe a week or two) to reabsorb moisture from the air? I think it's certainly advisable, ...
Graphus's user avatar
  • 63.5k
4 votes

Best way to cut a thin board that resists warping

Are you familiar with how the wood fibers are aligned in a tree? They (mostly) run from top to bottom and are bonded together with lignin. If you used the 'B' method the wood fibers would be running ...
Jambo's user avatar
  • 526
4 votes

What kind of woods can be riven with a froe?

You can really rive almost any wood. That statement is flawed as there are wood species, particularly those with long straight grain, that rive easier than others. It is important to know that species ...
Matt's user avatar
  • 20.1k
3 votes

How much extra thickness should I leave when rough milling green boards?

I believe there is just no easy "rule of thumb" when deciding what thicknesses to cut green lumber in an attempt to obtain a certain machined dry lumber thickness, without a lot of waste. Many ...
Gale Colby's user avatar
3 votes

Using thick branches to make an end-grain cutting board?

Interesting idea; it never occurred to me. I have a few narrow branches that I thought weren't going to be usable for much more than veneer, but using your approach if I can get a few 1"x1" cross-...
keshlam's user avatar
  • 9,171
2 votes
Accepted

Milling previously felled logs

Part of it depends on what you are planning to do with it. using it to make fine furniture, the limit is much earlier than if you are going to use it for more artistic pursuits such as turning bowls ...
bowlturner's user avatar
  • 15.6k
1 vote

Best way to source a lot of sub-1× lumber

"Best way" is very dependent on several different things. Your location is a big one, because that could put you very close or very far from a good source of the lumber needed. What kinds of tools ...
bowlturner's user avatar
  • 15.6k
1 vote
Accepted

Strength of board from squared branches as opposed to trunk wood

Structural lumber has continuous, well connected fibers running through the entire length of the board. Cutting those cells into 30cm/11" segments will significantly decrease the overall strength of ...
Ashlar's user avatar
  • 8,129
1 vote

Woodmizer LT40 - smallest diameter of log?

This may be obvious but the larger the log the more usable lumber returned. Since the lumber should be sawn to avoid capturing the pith that will limit log size somewhat. Time is the main factor. ...
Chuck S's user avatar
  • 859
1 vote

Panel Glue up Question

To get a flat panel, you usually need to start by jointing the glued edges to be extremely straight and perpendicular to the reference face of each board, and then plan on planing, scraping, and-or ...
keshlam's user avatar
  • 9,171

Only top scored, non community-wiki answers of a minimum length are eligible