Questions tagged [wood]

Specifically for questions about wood, the "raw" material itself (not to be used for questions about processing wood).

24 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
3
votes
0answers
43 views

dark stain for a mantle

I have a client that has me stumped. We installed a lovely new stone facade for a client, but their vision for the mantle has me at a loss. They like Minwax Carbon color stain, but want a deep color, ...
2
votes
1answer
127 views

What is the material that goes over Bathroom cupboards to give it a plastic shine look?

I am assuming it is some sort of laminate but I as the question states I am wondering when the material is that looks like a hard white plastic that goes over wood and tends to be used in bathrooms/...
2
votes
0answers
42 views

Knots bleeding through deck sealer

I have a deck that I built in 1986 with treated lumber, that last year we used a stain sealer on and the sealer was bled thru at mostly knot locations. I have used clear sealer many times over the ...
2
votes
0answers
32 views

Stairs-stain color Jacobean Miniwax

In middle of staining stair treads, the stain isn’t dark enough and can see the wood putty underneath. Do I just go darker with next coat-different shade? Or do I need to re sand and use wood ...
2
votes
0answers
98 views

Sanded and stained a pine window shelf… water damaged areas too dark. How to fix?

I am prepping my house to sell. We sanded and stained a window shelf under a Bay Window and the water damaged areas came out too dark. So how should I fix this? Sand again or stripper, or just cover ...
2
votes
0answers
379 views

Ideas for converting dining table to adjustable height coffee table

I have an old 3'x5' dining table sitting in the garage. I think it would be perfect to go in our den as a large coffee table so my wife can do her huge 3000 piece puzzles up there. The legs are ...
1
vote
0answers
34 views

Removing multiple layers of paint on oak decorative door frames

I'm making headway. I keep re-applying, scraping (plastic and steel wool), and wiping with mineral spirits. I have all low voc, etc., chemicals but how much can the little grooves in this wood really ...
1
vote
0answers
48 views

Questions about making mirror frame

I am trying to make a frame for a smart mirror, I have only made the inner frame(in the picture, the sides are 12 inches, and the top and bottom are 28 inches, the monitor is slightly smaller than the ...
1
vote
0answers
51 views

What about using cedar for toy puzzles and blocks?

Can cedar be used for making wooden puzzles and blocks for children?
1
vote
0answers
94 views

What is this antique wood object? Approx 10" long

What is this antique wood object?
1
vote
0answers
59 views

How soon should I cut up new wood?

I scored some pretty good logs of cherry from some workers across the street from my house who would rather have given it to me than lift it into the back of their truck. I carted it home and have it ...
1
vote
0answers
87 views

What's the name of this hinge?

I am planning to build a motorized bed. I am still in the researching phase so I went to a bedroom shop in my city. In the shop I saw this hinge, or at least I believe it´s called a hinge. I have been ...
1
vote
0answers
186 views

Bleeding bubbles through stain

Okay I saw another question about bleeding through paint but this is stain so it may have a different solution. I sanded, used prestain conditioner, and minwax stain on a desk I’m attempting to ...
1
vote
0answers
72 views

Can I attach a hinge to click laminate flooring?

This may seem like a strange question. Basically, I have some few click laminate floorings present with me and I would like to make a ping pong table from those leftovers. I was following this ...
1
vote
0answers
130 views

Tongue and Groove Scraps - Can you create a floor with them

I'm just finishing installing tongue and groove wood planks on my walls and ceiling. I have quite a few leftover small end pieces, especially at 45 degree angles (pitched ceiling). Can anyone think of ...
1
vote
0answers
180 views

Best method for making segmented rings for wood turning?

I am a wood turner, and like to do larger bowls. For segmented bowls, where you glue of rings of say 10 or 12 segments, then stack and glue segments to make the rough bowl blank, what is the best ...
1
vote
0answers
60 views

How to paint a piece of wood with spray

I've tried looking arround but posts are usually about giving a piece of furniture a certain color and such. I wanted to know if there is an accessible method for a newbie to paint (I was thinking ...
1
vote
0answers
423 views

Advice on making wood hinges

I am making some wood hinges for a table that will have a box in the back and simply open up. I did find a good design for making a wood hinge. The only question that remains: How should I cut the ...
0
votes
0answers
28 views

Blotchy finish on stain job

I sanded the western pine with 80 then 160 , I admit I put too much stain on at first to make it darker , now I have I have clear blotchy spots on it , any advice is greatly aprreciated! Thanks ...
0
votes
0answers
82 views

Exposure to a lot of oak sanding dust when didn’t know the harm…advice please!

I got into rustic oak furniture making a few years ago and used a belt sander and detail sander outside on the pieces (about 20 days solid in total spread over 3 years, but covered in dust). I also ...
0
votes
1answer
89 views

Making wood filler? - Pine + Glue

I want to make some wood filler for a pine cabinet. Was just going to mix wood glue and Pine sawdust.. Is there any ratio or anything I should do before i go ahead?
0
votes
0answers
51 views

Antique woodwork in 120 year old Victorian

What type of oil is best for caring for antique moldings and banisters in a 120 year old house?
0
votes
0answers
49 views

For how much time are fumes from freshly polished wood furniture toxic and must be aired out & presence avoided?

PS: If needs to be in the DIY SE rather than Woodwork SE please moderators figure where it will get better responses and fit. Thanks. PPS: Found this similar - https://diy.stackexchange.com/...
0
votes
0answers
84 views

Should I use spacing between boards on a chunky oak table?

I am building a solid oak (dried) table of 4 boards of 180 x 20 x 5 cm. This will stay in my home office in UK so temperature ranging between 18-28 degrees and humidity 40-60%. This is going to be a ...