Questions tagged [tools]

What tools to use, how to use them and when.

Filter by
Sorted by
Tagged with
4
votes
3answers
3k views

What are the differences between the K4, K5, and Foreman Pocket-hole Machine?

My husband is planning to make new cabinets for our kitchen and I'm looking at a Kreg Jig for him. What are the differences between the K4, K5 and the Foreman pocket hole machine?
6
votes
1answer
4k views

Why aren't belt sanders with sanding frames available anywhere?

I'm not sure if this question is a fit for Stack Exchange, but I'll try to make it fit. I bought a Bosch 1274DVS 10 years ago and I was able to get an accessory 'guide'. The guide was a frame that ...
5
votes
3answers
7k views

How do I prevent static on vacuum hoses?

Whether sucking up large amounts of sawdust at once or when attached to a tool, static electricity always builds up on my shop vac hoses when the dust passes through. This leads to messes on the hose ...
1
vote
1answer
216 views

Open Source Robotic Saw [closed]

I know that there are several opensource printers, i.e. RepRap. Are there any similar projects for robotic woodworking saw or other instruments?
16
votes
3answers
14k views

Caliper Showdown: Dial vs. Digital vs. Vernier

I recently purchased a digital caliper to make more precise measurements than a basic variety vernier and it works great. I wanted them to measure the width of my table saw for making my sled runners. ...
4
votes
2answers
1k views

What tool can cut thin wood or acrylic/plexiglass without melting it that is suitable for NYC apartment?

I live in NYC. I have a small roof deck but mostly must work inside and I have very little space to keep tools. I need to build cases for my electronics projects. Acrylic/plexiglass seems like a nice ...
10
votes
5answers
3k views

Are there alternative tools to a straight ironing rasp (or why are they so hard to find)?

I'm looking for a tool to smooth/flatten down a surface in a rectangular channel in the center of a piece of wood (I constructed the piece by gluing two halves together, but stupidly didn't clean the ...
7
votes
3answers
9k views

How do I identify hand planes?

I bought 2 hand planes last week at flea markets, both of them together cost me less than $20 (from 2 different places). Both of course needed some TLC, one was pretty orange on the top, bottom sides,...
4
votes
3answers
270 views

I need a critique on my sawing technique

When I am using larger hand saws, like my big rip saw, I have a problem when I pull back. The blade "buckles" and flaps back and forth. As a result pulling the blade back through is harder and the ...
9
votes
5answers
8k views

Making a small indent/crevice/depression for a ball

I am making my own wooden board game. The game pieces have ball-shaped bases. I want them to move around the board and rest in small indentations. Something like this: What kind of tools and ...
12
votes
3answers
15k views

Creating additional boards from thick lumber

I have boards that are ~ 2" thick, ~15" wide, and x feet long. I would like to divide these boards in half. I do not have the funds to buy a large bandsaw or other power tools. I'm looking to trim ...
13
votes
4answers
58k views

What are some suitable woods to use for tool handles?

We all occasionally have to replace a tool handle, be it an axe, a shovel, a sledge, whatever. The standard handle materials seem to be hickory and ash. I've bought my share of hickory handles from ...
13
votes
9answers
35k views

How to cut the centre out of a large round of wood

I have a large round of wood (horizontal slice of a tree) which is about 20 inches across (circle diameter) and 8-9 inches deep. I want to take the centre out of the wood, either by cutting a circle ...
12
votes
1answer
5k views

What is the hook angle on a saw blade?

One of the specs listed on saw blades is the hook angle. What does this mean, and when would you choose one over the other?
9
votes
2answers
1k views

Sharpening grits — naming and selection

Independent of all the different kinds of surface one can use to shape, clean, and sharpen tools -- and perhaps independent of whether said surface is motorized or not -- I have to admit to being a ...
12
votes
2answers
1k views

What are the advantages of band-saws with multiple speeds?

I'm currently thinking about buying a band-saw. While searching in my price range, I found that some models offer a single speed, others 2 and some even 3 speeds. I'm fairly new to band-saws and I ...
11
votes
2answers
1k views

Can you overwork an impact driver?

I recently got a 20v driver and impact driver set. Never had an impact driver before but I cannot imagine life without it. It makes it really hard to split wood by over driving and I love that. But I ...
8
votes
6answers
3k views

Why don't most modern drill presses use some form of VFD instead of manual belt-changes to adjust speed?

I was honestly surprised to see that most modern drill presses still use belts and pulleys (and the manual changing of them) to accomplish variable speeds. Does this design offer certain benefits that ...
6
votes
4answers
2k views

What's the best way to remove varnish from recycled wood flooring?

I've got a bunch of recycled hardwood flooring that I plan to use for shop projects and possibly nicer furniture. How should I remove the varnish? Would it be preferable to use the thickness planer ...
7
votes
4answers
2k views

Why would a plane have a grooved sole?

One of the planes I rescued from a yard sale has grooves in its sole, running front to back across the surface that contacts the wood. I'm having trouble imagining what their purpose could be, ...
10
votes
6answers
7k views

Easiest way for a beginner to reduce a pine board's width by 1/2"?

I have a small 20" x 24" x 1" pine board that happens to be 1/4" to 1/2" too wide for my needs -- the 20" side needs to be more like 19.7". What's the easiest/cleanest way for a beginner like me to ...
5
votes
3answers
1k views

How can I prevent homemade pipe clamps from twisting?

I would like to make some of these parallel clamps that use a pipe for the bar. Source The one advantage that commercial parallel clamps have over these is that the clamp faces will always line up; ...
12
votes
4answers
3k views

jointer cutter head : segmented spiral vs traditional knife design

I'm looking to replace the blades on our Powermatic Model 60 jointer, and was considering carbide blades.In particular I saw this cutterhead for the Powermatic Number 53, which is a 6 inch vs. the ...
14
votes
2answers
6k views

What is a try square used for?

I know there are many types of squares, and ultimately all of them are used check an angle for square-ness, i.e., to make sure it is a 90° angle. But different squares are good at different jobs. For ...
9
votes
9answers
14k views

What is the difference between a sabre saw and a jig saw

This is more out of curiosity. I came across the term sabre saw and tried to figure out what it was. Searching the internet turned up results for both a jigsaw: ...and a reciprocating saw: This ...
12
votes
7answers
31k views

Best method for drilling a larger diameter hole at an angle

I spent the weekend making a simple wine rack out of cedar for my mother as a gift. I drilled 1.5" holes in a cedar 2x6 to make something like this: So to keep the bottles inverted (keep the cork ...
9
votes
3answers
1k views

Is there a better way to make a wand?

I recently decided to make a magic wand with my son as a small project. He's been showing it off a bit (despite being very simple/basic), and now we've been asked to make a bunch more for family/...
7
votes
4answers
2k views

What to look for when buying a tap and die set (for wood)

I have never used a tap and die set but I find myself in the market to purchase some for a couple project I would like to do. What features should I be looking for, ease of use, etc.? Anything I ...
14
votes
2answers
649 views

What is the best way to get started with limited funds and space?

I enjoyed doing woodwork back in high school, but I haven't been able to do any since I started college. I want to get into it, but I lack the tools I had at the school shop, and similarly the space. ...
5
votes
3answers
781 views

What technique and tools can I use to create a straight canoe pole from a green tree

I'm using black spruce, white spruce, and tamarack to make canoe setting poles 12' x 1 ½" diameter. I look for standing green trees as straight as possible, maybe 1 ¾" at 13' height, then debark them ...
13
votes
3answers
10k views

Are there advantages to using pipe clamps over parallel bar clamps?

Pipe clamps seem to be a low cost and versatile option for gluing up projects. However, they're prone to racking the work piece if not placed correctly. Parallel bar clamps aren't as susceptible to ...
17
votes
4answers
40k views

How should I store the batteries of my cordless drill?

I have a nice cordless drill that came with two rechargeable batteries. However, there are times when life gets in the way and I'm not using the drill at all over the course of several months. When I ...
6
votes
1answer
1k views

What are the handles/wheels called when making a homemade vise (like a moxon?)

I would really like to make my own vises, like moxon, tail vise, etc. I'd love to be able to afford the benchcrafted kits but they are price-prohibitive. I've seen people make them out of press ...
7
votes
4answers
17k views

What tools do I need to start making cabinets?

I am looking for what equipment I need to start a minimal shop that will eventually be making nice cabinets. I have no preference for power tools versus hand tools. I already have a cheap contractor'...
9
votes
2answers
1k views

How do I use this hollowing tool?

I bought this Sorby hollowing tool (I just looked it up 2 years ago!) and I've never figured out how to use the dang thing. There wasn't ANY instructions that came with it, not even how to put the ...
9
votes
1answer
2k views

How to keep a hole saw together?

A few times I have purchased hole saw kits, there is one center piece and bunch of different sized saws every time I have tried to use one them by the second or third hole they are coming apart... It ...
12
votes
4answers
3k views

Do rip saws still have a place in the wood shop?

40 years ago when I was first learning to work with wood, there were crosscut and rip saws, each used for their own purpose. As I recall you could use a crosscut saw for either job. A rip saw could ...
12
votes
4answers
8k views

When do you use a chuck vs. a faceplate on a lathe?

I'm interested in learning to turn and recently bought an old Delta/Rockwell lathe that came with some basic accessories. I get the impression that a chuck and faceplate both serve the same purpose, ...
13
votes
2answers
3k views

What minimum amount of equipment is required to start turning bowls?

I'm curious to know what is the simplest set-up to start bowl turning? Which tools should be high-quality and which can I skimp on? I'm not interested in being able to turn a large variety of bowls, I'...
21
votes
5answers
4k views

When should I use a Jointer vs. a Planer?

I am fairly new to woodworking and just starting to outfit my shop with power tools. One area that I find confusing is the use case for a jointer vs. a planer. Both tools seem to have very similar ...
6
votes
1answer
104 views

Closing mouth on coffin plane

I have a Scioto coffin plane whose mouth is a little on the wide side. I'd like to glue a piece of wood inside the front of the throat to close it up, but I don't know if rubbing end grain against the ...
26
votes
18answers
34k views

How can I store hand tools so they won't rust?

I currently have a small set of hand tools, but do not use some very often. One hand saw that I own (stored on a shelf with my other tools in the basement) has rusted quite a bit on the blade, and I ...
8
votes
2answers
377 views

High grit sandpaper to sharpen a v-gouge

V-gouges are slightly difficult to sharpen. The inner part of the V is, in particular, difficult for me to get. I have read that you can actually use a very high grit sand paper, although I'm a little ...
11
votes
1answer
281 views

What are the main categories of wood-turning tools?

For example, you have the spindle gouge: A parting tool: And several more. Walk into any wood-working store, and you'll probably see many of these sorts of tools, among others, that come in a great ...

1
2