Questions tagged [joinery]

The process of joining two pieces (usually wood) together. Techniques, tools, hardware.

21 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
4
votes
1answer
328 views

How to hide base dados behind box joint corners

I don’t have any photos on me so hopefully I can describe this ok. Say I build a box like so: Cut the four sides. Cut dado in bottom of each side, on table saw (I don’t have another good way), which ...
3
votes
0answers
118 views

New Orleans style Exterior Wood Shutters

What process would you go through to create this style of shutters, with the expectation that they're built for long-life? Specifically, I'm interested in how the back panel is put together: glue or ...
2
votes
0answers
68 views

Would a dovetail key(s) in a beveled (mitered) chest panel be adequate strength for a larger box?

I'm building a hope chest for my daughter out of cherry, and wanted to use dovetails to join the panels. My hand-cutting skills aren't quite up to snuff for a fine detail like through dovetails, so I'...
1
vote
0answers
49 views

How to tell the correct fit on a mortise and tenon joint?

When making a mortise and tenon joint, it's important for maximum strength of the joint that the tenon fit inside the mortise properly: neither too tight nor too loose. If the tenon is too tight, ...
1
vote
0answers
94 views

Spindle moulder blocks and cutters

I have just purchased an old Tyzack spindle moulder (shaper) and need some help please. I'm new to carpentry and have never used a spindle moulder before. I am in need of a block and cutters. I ...
1
vote
0answers
77 views

Joinery Suggestions

I'm building a coffee table out of a live edge walnut slab. It's about 5'x30"x1.125" For the legs I've made some blue-stain ponderosa blocks, 18"x15"x2.25" Any suggestions on how to join the legs to ...
1
vote
0answers
255 views

Which weight bearing knockdown joints

I'm building a Murphy bed with 18mm plywood. I would like to use knock-down joints for the sides of the base (outer-frame). My research led me to cross dowels (see below) When doing some tests ...
1
vote
0answers
36 views

Choosing a finish for a tusk/key/wedge that stays put

To ensure that a tusk stays put longer in a mortise, is the nature of the finish critical (assuming the piece is cut to a L:W ratio ~10:1)? The particular type of construction i’m referring to is ...
1
vote
0answers
90 views

What's the name of this hinge?

I am planning to build a motorized bed. I am still in the researching phase so I went to a bedroom shop in my city. In the shop I saw this hinge, or at least I believe it´s called a hinge. I have been ...
1
vote
0answers
58 views

Would a threaded insert placed in or near the seam of a biscuit joint affect its strength?

Hopefully the question is clear. The threaded insert would be about a 1/2" long, and the lumber would be 8/4. The insert would be for a leg or a headboard bracket. If it would compromise strength, I ...
1
vote
0answers
600 views

How to build a window frame with hand tools?

I'm interested in the process of building a traditional 1920s America window frame with only hand tools and was wondering if someone could explain the basic process by which the pieces are cut, joined,...
0
votes
0answers
103 views

Best method of joining these two pieces seamlessly?

I will be creating a floating side table for my wife and am wondering the best way to join two pieces of wood. They will be joined in an “L” shape with the back of the L hanging against the wall and ...
0
votes
0answers
60 views

Brackets instead of pocket holes

I'm building a farm=style dining room table with thick legs. Dimensions are - 7 ft L x 38.5 in W x 31 in T, with tabletop being 1 inch. I don't know how to do pocket holes, can I use brackets ...
0
votes
1answer
57 views

Replacing cutout in oriented-strand board (OSB)

I cut out a small 4" x 5" piece of oriented-strand board out of a wall. I saved this cut out piece so I can re-attach it. When I put the piece back in the hole I cut, what do I use to re-...
0
votes
1answer
54 views

Joiner materials for larger than standard routing

The standard 5/32" biscuits seems a bit thin for a strong joint for thicker boards. A Feastool seems like the perfect tool, however it is a high price point for my volume. I have a 1/4" slot cutter ...
0
votes
0answers
37 views

Is Hide Glue suitable for gluing together Wooden Picture Frames?

I would like to Glue together the Mitred ends of some Beechwood, using Hide Glue. My concerns are ... Is Hide Glue strong enough? Does Hide Glue last? Therefore, is there any known instances ...
0
votes
0answers
160 views

How can I join 45 degree mitered boards as legs for a coffee table?

I'm looking to duplicate this look for a wooden coffee table: https://www.scandesign.com/products/porto-coffee-table Any ideas on how I could replicate those coffee table legs other than mortise and ...
0
votes
0answers
78 views

Reinforcing endgrain to long grain joint in thin stock, without visible splines?

I'll be building a small box soon, and one of the things I'll be drawing inspiration from is this photo I found online: I like the leg design of this box a lot, but it occurs to me that this is ...
0
votes
0answers
58 views

Perpendicular Hanging Bracket?

I'm building a saddlebag type of kayak rack on my dock walkway where the load-bearing cross beam travels under the walkway (vs on top as saddlebag implies). The walkway stringers are comprised of two ...
-2
votes
1answer
83 views

What is the best way to build a shelf?

How can I build a sturdy shelf out of pine boards? I can build a shelf out of plywood, however, I don't like the look, finish or the edges. I want to build a shelf out of 1/2" pine boards (...
-4
votes
1answer
140 views

What is the best way to cut a through slot in a board?

I want to cut some slots in a 1/2 board that I want to be very clean and square, so I would rather not use a chisel or anything like that. Here is an illustration: What's the best way to go about ...