Questions tagged [finish-selection]

Questions regarding finish selection for a project.

Filter by
Sorted by
Tagged with
2
votes
1answer
398 views

Finishing beech for minimal color change, matte finish

I'm trying to make a desktop out of beech wood (Ikea Gerton table top) and want the wood finish to look like this example photo... A very light natural, matte look. How could I achieve this while ...
2
votes
1answer
38 views

Oak veneer finishing

I just brought an oak veneer to decorate my apartment. (picture 1) However the colour is too white and I want to make it a little bit yellow as in the next picture. What would be the right wood ...
2
votes
0answers
37 views

Wooden desk, finish against urine

I'm repairing a used desk made from black carbo (it's harder than white oak to give an idea) which only had a wood wax finish. It's been damaged all around its base by dog urine. The old owner of the ...
2
votes
2answers
43 views

Sealing a Stained Poplar Bed Frame

I'm putting together a KD Frames poplar bed frame. I've already stained it with Minwax Wood Stain (I really wanted a black wooden look) but I'm unsure how to finish it. When I bought the stain at ...
2
votes
1answer
179 views

Finishing California redwood for a bed frame?

I'm looking at what finish would be best for a redwood bed frame. I would like the wood to look natural, warmish color, and a bit of a satiny feel. I've done a few trials and here is where I stand (...
1
vote
1answer
81 views

Filling Lines After Pyrography

I was wondering what type of filler I should use to obtain a clear coat that will fill the indents obtained after burning wood (see image attached) such that the two surfaces are flat (I'll probably ...
1
vote
1answer
129 views

How can I sanitize wood?

What can I do to wood before and after finishing a project to ensure that it is very clean and as safe as possible? I don't know about you, but I wouldn't eat off my work bench. Sometimes the wood ...
1
vote
1answer
41 views

How can I finish this to protect it from the elements?

I made this sign by gluing numbers made of birch bark to another piece of bark: This is for outdoor use where it freezes hard. The numbers are about 1/8 of an inch thick, and water will collect in ...
1
vote
1answer
390 views

What is a good non-yellowing finish for maple?

I am in the process of building a bench for indoor use out of hard maple. It will only get indirect sun when it is complete. This is my first project with this light of a wood (I've worked primarily ...
1
vote
2answers
111 views

Shelf building questions from a newbie

Good day all I want to start building a wooden "shelf" of sorts, the problem is that I have literally no experience. So I have been looking at a bunch of youtube tutorials and asking my stepdad for ...
1
vote
1answer
66 views

Choice of sanding sealer to avoid blotching (shellac vs cellulose)

I am working on a table that is made out of maple. I would like to apply a stain but maple is a timber that is prone to blotching so am considering using a sanding sealer before staining to reduce the ...
1
vote
1answer
113 views

Water-borne finish on red oak and want the natural red colour you get using oil finish

I will be using a water-borne finish on red oak and want the natural red colour you get when using an oil finish. How can I achieve this?
1
vote
1answer
55 views

Sealing and reinforcing particle board

I am making some picture frames from an old table. The table top is oak slats on top of particle board. I’ve sliced the table and trimmed the slices with walnut, and cut rabbets in the frames. Like ...
1
vote
1answer
441 views

Finishing/Buffing/Polishing Redwood Slab with Oil-based Varnish thinned with Danish Oil

I have a 3x5 ft Redwood slab with 1 coat of varnish/danish oil (50/50) mixture and 1 coat (last applied) of just varnish. I applied fairly thick coats for both layers. The varnish The Danish oil I ...
1
vote
1answer
1k views

How should I polish and finish this table top stained with Minwax Polyshades?

I built a dining tabletop out of pine and stained it three times with Minwax Polyshades Pecan and a fourth time with Minwax Polyshades Espresso. The fourth coat was just to get the rough looking ...
1
vote
1answer
146 views

How can I protect my teak table while maintaining its raw and unfinished look?

I have an outdoor teak table that I want to be protected against the weather without altering the way it looks too much. I put clear spar urethane on my chairs and was unhappy because they ended up ...
1
vote
1answer
239 views

What finish can I apply to mixed end-grain/cross-grain bowl that's sanded to 7000?

I'm new to woodturning. I've made a small bowl from layered woods. I don't know what these woods are as they're reclaimed, but it's a red-coloured wood sandwiching some pale wood. I think the red-ish ...
1
vote
1answer
59 views

Matching a cheap yellow finish on oak

Is there a method for matching an unknown finish on an existing piece of wood? In my case, I have an old (but nowhere near antique) piece that has had a couple trim pieces fall off. I've managed to ...
1
vote
0answers
91 views

What finish should I use on wooden jewellery?

So, I'm carving a wooden pendant for my girlfriend. I want the finish to be satin. However, since she plans on wearing it all the time, I want it to be water resistant. I do not want the wood to get ...
0
votes
1answer
761 views

How can I harden soft woods?

I want to build a coffee table out of cedar planks treated with the Shou-Sugi-Ban method. The problem is that cedar is too soft for regular use and will get notched and scratched very quickly. How ...
0
votes
1answer
65 views

Finishing Red Cedar Tabletop

I'm currently in the process of building a red cedar tabletop with laminated live edge slabs. Thickness should be around 7/4. However, I'm unsure what to use for finishing it. Given the wood is so ...
0
votes
0answers
48 views

For how much time are fumes from freshly polished wood furniture toxic and must be aired out & presence avoided?

PS: If needs to be in the DIY SE rather than Woodwork SE please moderators figure where it will get better responses and fit. Thanks. PPS: Found this similar - https://diy.stackexchange.com/...