I am working on a design for a hardwood door that would feature square, pyramidal panels. In masonry such shapes are called "diamonds". The question is how to shape the panels and do the joinery into the structural members of the door. I have shown the section and elevation below with approximate measurements:

pyramidal panel

Trying to cut the panels out of a single slab of 2" board has challenges, but on the other hand trying to make them in pieces also has complexities.

  • +1 for inspiring a lot of creativity in the answers!
    – FreeMan
    Commented Jun 6, 2019 at 11:53

3 Answers 3


The traditional way to do this, is to have the central diamond be on piece of wood, and the raised portions around the edge be a separate frame. The frame is held together with mortise and tenon joints, and has a groove into which the central panel fits. The central panel is not glued in place, to allow for expansion.

Normally, the central panel is a constant thickness over most of it's width - it's just the edges that are cut back. You can do this with a spindle moulder. For this design though, I think you would want a spindle-moulder to do the edges, and then mount the piece in a jig, and feed it through a planer-thicknesser. You'll have to feed it through once for each plane of the diamond - so eight times in all. Getting the jig right is going to be fiddly!

  • The central panel could consist solely of the raised diamond portion. Then cut a groove (mortise) around the outside edges and the flat pieces would be tennoned into that (without glue) to hold it into the door frame. This would allow cutting the diamond panel in a single pass on a table saw by holding the panel vertically with the blade set at the appropriate angle. The flat pieces between the diamond and the "main" door frame would, essentially, be very wide, visible splines holding the 2 sections together. They would probably need to be cope & stick joined to hold them flat.
    – FreeMan
    Commented Jun 5, 2019 at 13:12
  • 2
    "Cut in a single pass" - each face of the central diamond would be cut in a single pass across the table saw. 4 passes per side, 8 in total. However, it would only take adjusting the saw one time. NOTE: you would need the appropriate jig/fixture to hold the board vertically to safely cut it without losing fingers and/or throwing lumber across the shop. (hint: Google for "tenoning jig".)
    – FreeMan
    Commented Jun 5, 2019 at 13:15
  • I thought about the planing method. The main problem is that the rebated parts of the panel must be 4 separate pieces 2/3" thick that are tenoned into both the frame and the panels. This might be fine, but I thought it might be weaker than tenoning the panels directly into frame. Commented Jun 5, 2019 at 13:47
  • 1
    @FreeMan Unless you've got a 12" blade you're not going to be able to cut that on a tablesaw. He wants it to be 8" across, so each cut would need to be 4"+ deep and a 10" saw maxes out around 3". Commented Jun 5, 2019 at 15:52
  • @SaSSafraS1232 good point. It might actually be easier to do in a radial arm saw - it might have the depth of cut, and it would be reasonably easy to create a stable, braced box to hold the board on edge. TBH, I think the only one of those I've seen in the last 20 years is at my father-in-laws and is probably older than I am...
    – FreeMan
    Commented Jun 5, 2019 at 16:11

One option if you don't mind a little math, careful blade height adjustments, and using a hand plane:

Calculate the depth at a series of distances from the center of the pyramid, say every quarter inch. Set a table saw blade height (carefully) to that depth and cut concentric squares around the pyramid at each corresponding depth. Make sure the inside of the kerf (from the center) is aligned to the calculated position.

Then, using a shoulder plane, remove the remaining ridges to the point where the cuts disappear and then flatten the angled surface.

This is a bit of work but with a nice sharp plane it will go faster that you might imagine. A second plane with a more aggressive setting could help with removing the bulk. One problem here will be going across the grain on two of the sides depending on the species of wood.

  • +10 for doing it using hand tools. "I wonder how they did stuff like this in the old days?" Apart from my innate preference for hand tools, regardless of the powered option chosen surely the amount of post-machining sanding that will be needed in at least some cases is going to pose a big challenge to maintaining the sharp arrises.
    – Graphus
    Commented Jun 6, 2019 at 7:25
  • 2
    @Graphus Agreed, love hand tools but this isn't pure. I think you could use a router plane to cut the grooves to a precise depth if you couldn't use a modern table saw. You might like "The Woodwright's Shop" on PBS, if you haven't seen it. WARNING: Contains puns and other corniness.
    – JimmyJames
    Commented Jun 6, 2019 at 15:24

The diamond piece could be cut with a router planing jig - basically, a pair of rails that sit on your work table, along with a sled that your router is mounted to. The sled rides on the rails, which allows the cutter to move along a 2-D plane a fixed height above the work table. It's almost like an upside-down router table, in the sense that your workpiece is fixed and your router is moving in relationship to it with the relationship defined by the rails. There are many examples available on google or youtube if you're unfamiliar - starting to use router planing jigs a few years ago has really changed the way I do many woodworking operations for shaped panels like this.

Your workpiece would be clamped between the rails, with a shim underneath one edge to raise that edge up off the work surface and set the angle at which you want to cut the facets. The shim could be screwed or clamped to the work table in a fixed position, which would allow you to turn the workpiece through 90 degrees and clamp it back down to cut each of the 4 facets. Then, double the height of the shim, flip the piece over, and cut the 4 facets on the opposite side.

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service and acknowledge you have read our privacy policy.

Not the answer you're looking for? Browse other questions tagged or ask your own question.