I'm planning to build a 72x30x2" table top and only own a table saw. After reading some guides, it looks like most people will cross cut the edges to the final dimensions with a track or circular saw. Is this entirely necessary or could the same be accomplished on the table saw with the same accuracy?

  • AFAIK most people don't do this on their table saws because the tables of their saws aren't large enough, and the typical crosscutting sled is too small also. If the table saw;s working area and the crosscut sled are large enough to accommodate the workpiece however there's no reason this sort of cut can't be done on one. How about doing it by hand?
    – Graphus
    Nov 26 '18 at 7:53
  • You've accepted your Answer here which I presume means you're aiming towards doing this with a circular saw but I want to make the case again for doing this by hand. A decent crosscut saw is an excellent investment for any woodworker, no matter how heavily centred on power-tool woodworking, not just because of their innate value (modern saws have a useful lifespan of a decade + in the hands of the typical woodworker, while only costing <20 bucks) but there are so many cuts you can do faster and more safely with one, And there are cuts only a handsaw allows, so easy must-have argument there.
    – Graphus
    Nov 27 '18 at 15:02

I don't think you're going to get the result you want if you make these cuts with a table saw. Cutting large pieces on a table saw comes with a lot of challenges in terms of maintaining the alignment of the work piece with the blade to get a clean, consistent cut. And cutting large pieces always brings the risk of kickback from your saw.

I sometimes sort woodworking cuts into two categories:

  • Cuts where you bring the work piece to the tool (e.g., a cut made with a table saw, a hole made with a drill press, etc.)
  • Cuts where you bring the tool to the work piece (e.g., a cut made with a circular saw, a hole made with a cordless drill, etc.)

Generally (in my view), the larger the piece, the more it makes sense to bring the tool to the work piece, and the smaller the piece, the more it makes sense to bring the piece to the tool. It basically comes down to which of these is easier (and often safer) to manipulate through the operation. You're looking at making a series of long cuts on a very large work piece.

Although, as Ashlar pointed out, it is possible cut full sheets of plywood on a table saw, the setup needed to do this is much larger than a typical contractor's saw. My table saw can make these cuts, and I still avoid it whenever possible. Plus, a 2" thick glued-up top will weigh an awful lot more than most plywood, which will only add to the handling challenges. Further, the edges of plywood aren't typically a finish surface, so any tearout, burning, or other imperfections generally get hidden by other parts of the finished piece. For your table top, either the cuts will be show surfaces, in which case you want really clean cuts, or they'll be glue surfaces for breadboard ends, in which case... you'll want really clean cuts.

Even if you don't own a track saw or circular saw, maybe see if there's a way for you to borrow or rent one. If it's in your budget, a decent circular saw can be had for not a huge amount of money, and you can fashion up a guide to help you align the cut.

  • +1 for just buying a circular saw. They're useful outside of woodworking if you're a homeowner, too, so it probably won't be a single-purpose tool.
    – mmathis
    Nov 26 '18 at 21:09
  • 2
    I've upvoted this as it's definitely a useful Answer and quite comprehensive but I do want to say something about quality of cut, I don't think in an of itself that should be decider given the alternatives may (and often will) give a result equally good if not inferior to those possible on a table saw. Additionally, cleaning up a sawn end-grain surface should be taken as a given, so quality of cut becomes relatively/somewhat unimportant — just to be clear, not commercially but for the average Joe where more time needed isn't a dealbreaker..
    – Graphus
    Nov 27 '18 at 15:28

Table saws are often used to cut full sheets of plywood, so your table top can certainly be cut with great accuracy provided you have adequate support for the panel at infeed, outfeed, and side. The outfeed and side are usually supported with mobile tables and rollers and I have seen fold up tables hinge attached to the table saw in lieu of tables on the internet. I provide infeed support using rails similar to the ones shown in the picture (https://jayscustomcreations.com/2014/06/table-saw-infeed-support-arms/). It is very important that the panel have full support for the full duration of the cut so that you need only be concerned with pushing the panel across the blade snug with the fence.

Tablesaw infeed rails

  • Thanks! This seems to be a good idea for sheet goods but probably would be too unstable for a 90 pound table to be cross cut accurately. I'll certainly use this tip for sheet goods though.
    – Tom S
    Nov 27 '18 at 6:14
  • I've built and used one and believe it will easily support 90 lbl.
    – Ashlar
    Nov 27 '18 at 17:48

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.