I am building a laundry basket out of MDF. I need to paint it. How should I proceed once the basket is glued together? (Sanding?, priming?, painting?, other?)

  • 1
    Is this a basket you will use to transport laundry, or is it more of a hamper, which you just use to collect dirty clothes? Keep in mind that MDF will make for a rather heavy laundry basket, and will not hold up very well to wet laundry if water is able to get past the paint (e.g., at joints and screw holes).
    – rob
    May 29 '15 at 1:48
  • I guess it's more of a hamper. It's to collect dirty clothes until the next load of laundry. We typically avoid putting wet clothes in any basket/hamper until they are fairly dry. May 29 '15 at 1:58

Sanding?, priming?, painting?, other?

  • break sharp corners: Sharp outside corners are easily damaged, and they don't hold paint as well as not-so-sharp corners. You can "break" the corners with a sanding block or just some sandpaper held in your hand. A router with a small-radius roundover bit works really well -- I use a 1/16" radius bit.

  • prime before painting: The smooth faces of MDF can be painted without a lot of preparation, but a coat of primer will seal the surface and give the final coat a smoother finish.


There should not be much to this. One of the main advantages of MDF is that it is paint ready.

There are still some things you need to consider where the drawbacks of MDF come into play. Rob brings these up in his comments so I mention them here at an attempt of completeness.

  1. Weight - MDF is very dense which makes it heavy. Depending on the thickness you could end up with one heavy load. (Nothing to do with painting of course but still worth mentioning.)
  2. Water absorption - A couple of points in this regard. If you have laundry in there and your MDF is not sealed against that it will make the MDF swell. The is more important at the edges like where you might cut handles or near joinery.

Leading from that I would only suggest that you prime if you plan to use a lighter colour and don't want to have to worry about MDF brown ruining the look. If you do prime make sure you don't use a water based primer for reasons mentioned above. If your actual paint of choice is water based based then priming would be a good idea!

There are also suggestions about sealing the edges of MDF which should be considered. This might also come into play if your basket is more that just a simple box with handles. Using a mud or spackle is recommended since, like end grain, the edge of MDF will absorb paint irregularly. Since it is likely that moisture will come into contact with this project you should do what you can to protect it. Covering all exposed edges and after it dries just sand it down.

Should be a good start to a great laundry basket I think.


Good advice here from Matt and Caleb.

Just thought I'd tell you how we do it where I work:

We use MDF all the time, including moisture-resistant MDF for external boarding. We also sometimes run V-grooves or flutes into the faces of boards for a decorative detail.

Before painting, we sand all faces, paying particular attention to cut edges (so the edges of boards or any cut-outs), also making sure to sand a small (~0.5mm) chamfer to any sharp edges. Then we seal the cut edges with standard timber end-grain sealer (but you could probably use PVA glue), then paint with a primer, nib and paint with topcoat. This gives a good smooth finish every time.

I would not skip the edge-sealing stage, if you're going to have any of the edges visible, as if skipped this will give a very rough-looking edge and will absorb the paint inconsistently. A good coat of primer might do it, but it would depend strongly on the type of paint/primer you're planning to use.


You can prime and/or paint the faces of MDF immediately if you wish. Sanding is not strictly necessary, although it can help primer or paint adhesion, will remove surface contaminants as Graphus mentioned in a comment below, and can smooth out small dents and scratches as WhatEvil mentioned.

As Matt and WhatEvil mentioned, it's also a good idea to seal the edges (e.g., with with drywall compound) before priming and painting.

  • Sanding may not be strictly necessary, but it will improve the finish as paint can stick more easily to a rough surface. There are also often small dents or scratches on MDF boards.
    – WhatEvil
    May 29 '15 at 8:03
  • 1
    @WhatEvil, there's plenty of microtexture on even the factory surfaces of MDF for paint to adhere to, I'd be doubtful that sanding would actually increase this usefully. What sanding might do however is remove surface contaminants from handling, which can definitely negatively affect paint adhesion (as it does with glue bonds).
    – Graphus
    May 29 '15 at 9:29
  • Graphus is right. The internet backs him up as well. One reference finewoodworking.com/how-to/article/tips-for-painting-mdf.aspx
    – Matt
    May 29 '15 at 10:37
  • Granted, it's probably OK unsanded, but we get a noticably better finish after sanding in our workshop, with the water-based paints we use. Also, quote from your link: "I usually scuff-sand the surface quickly with 120-grit or 150-grit sandpaper to remove any dirt and grime and to provide for better adhesion of the primer coat." Plus my point about small dents and scratches still stands.
    – WhatEvil
    May 29 '15 at 11:01
  • I was a bit hasty with my original answer; thanks for the feedback.
    – rob
    May 29 '15 at 12:15

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.