I am currently trying to work on a project that involves piercing a lot of large-diameter (~38mm) holes in rather thick (~5cm) bamboo board sheets.

For that, I am using a hole saw. However, I ran into the problem of the wood starting to burn and the bit getting stuck (due to the thermal expansion?).

If I was drilling or routing metal, I would be cooling with a mix of oil and water at the ambient temperature.

What can I use to perform similar cooling in the context of working on wood? Would water be sufficient? Should I just make frequent pauses and let the drill bit cool in the air?

  • 1
    Just to clarify, it sounds like you're talking about a hole saw? Oct 23, 2019 at 14:11
  • 1
    You can periodically dunk the bit in water to cool if needed, yes. But there are other tips that can help reduce load (and hence overheating) some of which will also simultaneously help reduce or eliminate the puck becoming stuck in the hole saw. Two immediate things you can do are to check sharpness (and touch up or replace the bit if needed) and making sure that there is no resinous buildup anywhere on it, in the gullets (the gaps between saw teeth) as well as inside or outside surfaces of the cylinder.
    – Graphus
    Oct 23, 2019 at 14:15
  • 1
    I've made an edit to the wording of the title and the body of the Question but as I was writing a fuller Answer it occurred to me I may have been too hasty in assuming you were using a hole saw. Please edit if I've made a mistake and provide a link to the type of bit you are using.
    – Graphus
    Oct 23, 2019 at 14:32
  • 1
    @Graphus: You are indeed correct - than you! I did not know the name of this tool in English :)
    – chiffa
    Oct 24, 2019 at 16:39
  • 1
    Some carbide hole saw have very deep gullets that remove saw dust much better. Bamboo is very hard on saw teeth and will dull quickly. Oct 24, 2019 at 19:01

3 Answers 3


This was mentioned in SaSSafraS1232's answer, but it works so well that I think it deserves an answer all on its own.

If you're using a hole saw and planning on cutting all the way through the work piece, then I strongly suggest you start by drilling one or more relief holes for sawdust before you use the hole saw.

Drill the relief hole on the kerf of the planned cut with the hole saw, such that the relief hole is mostly on the waste side of the hole that will be cut with the hole saw, but still overlaps the kerf of the hole saw. Here's a picture to help illustrate the technique:

Sawdust relief hole on hole saw kerf

Image Credit: Family Handyman (original article)

The problem with heat and burning is that sawdust builds up and has nowhere to go. One way to fix this is to slow down and clean out the kerf often. Another way to fix it is to drill holes as above. It gives the sawdust somewhere to go as you cut.

You'll still have to go slow. Check the relief holes periodically to see if they've gotten clogged. If they do, the heat will start building up and you'll get smoking and burning again. But with the relief holes, you can drill with the hole saw longer before you need to stop and check things.

The difference in quality of the resulting hole saw cut with a relief hole vs. without is just huge.

  • Thanks! I’ll try that approach - it seems the most simple for me, since it requires no additional bits purchase. Let me come back once I test it.
    – chiffa
    Oct 24, 2019 at 16:51
  • 2
    Nice approach for larger holes where Forstner bits may not be big enough, or where you only have a holesaw handy.
    – user5572
    Oct 24, 2019 at 18:53
  • 1
    @jdv I definitely prefer a Forstner bit most of the time. But with bigger holes, the hole saw is the way to go. Also, some material (like hardboard or MDF) dulls a bit faster, and depending on what I'm building, I might prefer to use a hole saw instead of dulling my Forstner bit. Also, if you already have hole saws, but not Forstner bits, this technique is good to know about. Oct 25, 2019 at 6:19
  • @KatieKilian - that's what I did and it ended up working really well! With a slightly more powerful drill I ended up doing the 21 holes I needed in under two hours.
    – chiffa
    Mar 9, 2021 at 8:59

The problem with hole saws is that there is no way to eject the waste. If the waste sawdust is properly dealt with the saw will not heat up to the point of scorching.

In a normal twist bit the waste is pulled out by the grooves in the bit. With no grooves the waste from a hole saw clogs the gullets and packs in around the sides of the bit, heating it up and increasing friction. This is actually the cause of the binding you're feeling, not thermal expansion (or possibly alignment issues, see jdv's answer for more info). There's usually plenty of "set" on a holesaw (i.e. the teeth project well outside the thickness of the tube) to prevent binding on the work piece itself.

The best way around this is to keep a compressed air blow gun handy and stop, pull the bit out, and blow the hole out every so often (every 1/8" of depth or so). At the same time you should also pick or blow off any sawdust packed in the gullets of the saw.

You can also drill holes in the waste that overlap with the kerf the saw is cutting to give the waste somewhere to go. Just be careful not to let them wander into the "keeper" side of the cut. This is easier with brad point or forstner bits.

  • Thanks! I ended up going with drilling holes as you mentioned and it actually worked really well for me - I used the @katie-kilian's image as a guide and it worked really well.
    – chiffa
    Mar 9, 2021 at 9:01

To answer your question: the DIY or home wood shop doesn't generally use any sort of bit lubrication or cooling liquid. Maybe some applications would use some sort of wax or teflon coating on the bit, but I wouldn't bother.

Use sharp appropriate bits for the material and adjust speed and feed accordingly. It sounds like you are using a hole saw, which has a few problems:

  1. They don't clear chips well, clogging the hole and adding to the overall work load
  2. They often have a greater amount of finer teeth, with little kerf and not much gullet necessary for clearing chips
  3. The large rotating part that holds the teeth is almost always going to rub against the work no matter what you do, holding all that heat and causing burning

Hole saws are really only appropriate for specific applications.

The typical use is to go slow and straight -- try not to rotate the bit out of round around its axis or you will wallow out the hole and cause more friction. Nice even and straight pressure is best, with plenty of breaks to clear chips. A source of compressed air is handy in this case.

Alternatively, you can get a few Forstner bits that are the right size. Get one with the centre a bit proud so you don't have to drill pilots holes. Again, adjust your speed and feed, and allow the chips to clear. Forstner bits have less trouble with clogging, so you might be able to just blow the chips away as you work with puffs of air.

This is also a place where keeping square and true to the hole is important. Two much pressure to one side is where the friction and burning comes from. A drill press or guide is handy in this case. Though, I've had luck with careful hand placement and a centre spirit bubble attached to the base of the drill, in line with the tool bit.

  • 1
    Since this link is doomed to be dead in an internet moment, I'll add a link to cheap and cheerful drill guide I've had luck with when drilling lots of straight large holes: milescraft.com/product/drillmate
    – user5572
    Oct 23, 2019 at 14:15
  • Did not know about Foster bits, thanks! I was thinking about using a stepper bit to progressively increase Hope size, but I will first try drilling dust evacuation holes.
    – chiffa
    Oct 24, 2019 at 16:49

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.