Woodworking Beta

Editor

 Editor
First edit.
Awarded 761 times.
How to level plywood/OSB shed floor
Awarded Jan 10 at 20:35
Number of polyurethane coats before I can polish?
Awarded Jan 7 at 21:05
Will faster drying interior polyurethane work over a layer of slow drying exterior poly
Awarded Jan 6 at 1:17
How do you make mortise and tenon joints using power tools?
Awarded Dec 31 '20 at 4:27
Identification of vintage wood lathe tail stock
Awarded Dec 30 '20 at 18:48
Planing to correct cupping in panel (desk top)
Awarded Dec 28 '20 at 16:18
Restoring old oak chair but at a loss for something I've never seen
Awarded Dec 21 '20 at 22:35
Veneer and Air Bubbles
Awarded Dec 21 '20 at 19:01
How to finish a wooden ironing board?
Awarded Dec 20 '20 at 23:18
How do I calculate the weight capacity of my one side supported bookshelf (Spine Booshelf?)
Awarded Dec 19 '20 at 11:04
Is there a Bagless Dry Vacuum for Shop/Garage Use?
Awarded Dec 18 '20 at 12:35
Is there a Bagless Dry Vacuum for Shop/Garage Use? [closed]
Awarded Dec 17 '20 at 16:56
How to Attach Sides to Rabbit Pen
Awarded Dec 12 '20 at 23:11
Repairing a half lap joint in table leg x-bracing
Awarded Dec 12 '20 at 22:12
Failed table leg glue up removal
Awarded Dec 12 '20 at 15:41
How to remove and repair a crooked desk leg?
Awarded Dec 11 '20 at 18:25
How to repair a warped kitchen tabletop?
Awarded Dec 6 '20 at 22:11
How to make a stronger butt joint where two panels meet
Awarded Dec 5 '20 at 20:04
Drill press, chuck falls down. How do I repair?
Awarded Dec 5 '20 at 19:26
How to smooth out grain texture from shellac?
Awarded Dec 3 '20 at 17:40
What are the differences between a single flute countersink bit and a five flute countersink bit?
Awarded Dec 1 '20 at 6:47
Notching and dimensioning a lot of 2x lumber to a specific size
Awarded Nov 12 '20 at 19:07
How to make bent bed slats?
Awarded Nov 4 '20 at 2:21
Any tricks for transferring an angle that needs to be pretty perfect?
Awarded Nov 2 '20 at 10:51
Overpainting corner hutch
Awarded Oct 31 '20 at 12:46
What grit sandpaper should I use on my drumsander?
Awarded Oct 30 '20 at 21:27
Circular Saw Throws Wood at End of Cut
Awarded Oct 27 '20 at 14:05
How can I dry lumber outdoors for furniture?
Awarded Oct 26 '20 at 14:35
How do I calculate a miter angle?
Awarded Oct 25 '20 at 4:25
How do I thin down an existing thick log-slice cutting board?
Awarded Oct 23 '20 at 18:03
Clearance hole for partially threaded screws
Awarded Oct 21 '20 at 11:40
Using a 5/8 dado stack on a “30mm” arbor
Awarded Oct 21 '20 at 6:25
Curing no-VOC finishes indoors?
Awarded Oct 18 '20 at 14:47
What are some suggested methods to cut kerfs in long deck boards?
Awarded Oct 17 '20 at 15:26
How can I make a hole with a keyway in wood?
Awarded Oct 14 '20 at 16:18
(post deleted or otherwise unavailable)
Awarded Oct 11 '20 at 20:10
When should I use high speed and when lower speed with a drill press?
Awarded Sep 28 '20 at 16:50
How to preserve sole of transitional plane
Awarded Sep 27 '20 at 22:26
Track hardware for hanging plywood panels
Awarded Sep 27 '20 at 20:56
Is it safe to use a Craftsman molding head on a shaper?
Awarded Sep 24 '20 at 10:11
DIY Desk - Pipe Z-Frame dimensions issue
Awarded Sep 24 '20 at 1:17
Levelling off a surface for veneer
Awarded Sep 18 '20 at 18:50
Strengthen a post and beam structure
Awarded Sep 9 '20 at 17:50
Nails plus glue into endgrain vs screws plus glue vs dado (for shelf)
Awarded Sep 7 '20 at 19:05
Brackets instead of pocket holes
Awarded Sep 5 '20 at 0:01
Adding a “plank” like section to the edge of a table to allow for monitor stands/ mic stands
Awarded Aug 31 '20 at 23:27
One spot on a plywood does not accept stain. What can I do?
Awarded Aug 29 '20 at 17:58
How did I bend this router bit? What safety or operating step did I miss?
Awarded Aug 18 '20 at 23:03
Replacing cutout in oriented-strand board (OSB)
Awarded Aug 4 '20 at 2:55
What are the sound frequencies (Hz) of common woodworking machines?
Awarded Aug 2 '20 at 21:15
Basic router/bit question
Awarded Aug 1 '20 at 6:03
(post deleted or otherwise unavailable)
Awarded Jul 28 '20 at 11:26
Legs from 3/4 plywood.. load capacity
Awarded Jul 24 '20 at 21:05
Best finish for an outdoor woodworking bench
Awarded Jul 24 '20 at 7:35
Half-lap joints for day-bed build?
Awarded Jul 23 '20 at 19:25
Structural recommendations for a farmhouse table with a lapped, crossed legs
Awarded Jul 22 '20 at 3:11
Building a Rolling Wall, Step 1 The Base
Awarded Jul 21 '20 at 13:48
Why is this planing job going so badly?
Awarded Jul 21 '20 at 12:02
Best way to mount bench vise for my particular bench?
Awarded Jul 19 '20 at 18:40
Is Khaya more durable and a better flooring choice (based on quantitative hardness, density, etc.) than “genuine mahogany”?
Awarded Jul 18 '20 at 1:18
1
2 3 4 5
…
13