Woodworking

Enlightened

 Enlightened
First to answer and accepted with score of 10 or more. This badge can be awarded multiple times.
Awarded 168 times.
Adapting a 4-jaw drill chuck to hex shanks?
Awarded Oct 4, 2023 at 23:28
How does a worktop jig work?
Awarded Aug 31, 2023 at 0:58
Drilling very small holes in softwoods
Awarded Jul 21, 2023 at 13:36
How to apply polyurethane?
Awarded Jul 2, 2023 at 7:56
What kind of finish should I use inside dresser drawers?
Awarded Feb 10, 2023 at 0:09
Why are table legs attached to the edge of tabletop so rare?
Awarded Sep 29, 2022 at 19:50
Another router profile - which bit to use?
Awarded Aug 26, 2022 at 16:41
How can I identify sharpening stones?
Awarded Aug 26, 2022 at 8:41
Is there anything a dual bevel mitre saw can do that a table saw can not?
Awarded Aug 10, 2022 at 13:08
What type of table saw blade is best for jointing?
Awarded Feb 1, 2022 at 19:17
What is the difference between MDF and MDO?
Awarded Jan 19, 2022 at 13:56
Repair a crack on the side of an oak table
Awarded Jan 18, 2022 at 18:35
Orbital sander papers coming off
Awarded Jan 4, 2022 at 5:10
How do I make a mortise and tenon joints by hand
Awarded Oct 8, 2021 at 8:25
Hand planing edge joined board without tearout
Awarded Jun 30, 2021 at 20:34
I accidentally used woodglue that doesn't stain. How do I fix it?
Awarded Jun 4, 2021 at 2:51
Is it safe to use just the chippers in a dado stack?
Awarded Apr 20, 2021 at 17:53
What are the different grain directions, and how do they affect joint strength?
Awarded Apr 18, 2021 at 9:41
Can you overwork an impact driver?
Awarded Jan 28, 2021 at 14:51
Can I expect an improved weekend shop experience from installing an air filtration system?
Awarded Jan 14, 2021 at 17:52
How can I tell if wood turning (lathe) chisels are sharp?
Awarded Dec 14, 2020 at 8:47
which direction does wood expand?
Awarded Dec 4, 2020 at 6:20
What are Rockwell points?
Awarded Nov 25, 2020 at 17:32
Unknown tool from auger bits set
Awarded Nov 23, 2020 at 13:41
Comparison of Western saws and Japanese Saws
Awarded Jul 31, 2020 at 15:05
What common woods produce the safest/most harmful dust?
Awarded Jun 30, 2020 at 0:48
How can I hollow out a square hole in a solid piece of wood to make a box?
Awarded Jun 11, 2020 at 5:11
Design considerations for a machinist's work bench
Awarded Feb 12, 2020 at 20:05
Angled cuts without miter saw or miter box?
Awarded Dec 3, 2019 at 0:50
What is the name of the hardware used in these MDF joints?
Awarded Aug 9, 2019 at 8:35
Lumber crayon versus crayola...what's the difference?
Awarded Aug 8, 2019 at 6:50
Best way to hide counter sunk screws
Awarded Jun 10, 2019 at 17:30
Why a 5hp 14" table saw?
Awarded May 12, 2019 at 1:00
Good way to sand wide curved faces
Awarded Apr 28, 2019 at 11:45
Gluing joints with no clamps
Awarded Feb 23, 2019 at 4:00
How can I make this faux inlay?
Awarded Feb 8, 2019 at 11:10
Can I speed up stain drying with a hair dryer?
Awarded Nov 11, 2018 at 9:50
Triangle Screw & Double Sided Eyes?
Awarded Nov 9, 2018 at 19:40
What kind of plane is this?
Awarded Oct 17, 2018 at 22:25
How do I achieve flush joinery when the pieces need to be stained differently?
Awarded Oct 17, 2018 at 2:10
How do biscuits work?
Awarded Oct 9, 2018 at 16:25
How do I carve an inset circle?
Awarded Aug 13, 2018 at 11:15
Is a shorter rip fence safer?
Awarded Jul 26, 2018 at 2:05
Is there any such thing as sanding something *too* fine for finishing?
Awarded Jul 18, 2018 at 18:58
What sort of dust collection system would be adequate for a two-car garage?
Awarded Jul 2, 2018 at 4:47
What is wood stabilization?
Awarded Jun 14, 2018 at 19:50
How can I cut a 90 degree angle with a table saw?
Awarded Jun 5, 2018 at 2:43
What is the difference between full overlay and half overlay hinges?
Awarded Mar 29, 2018 at 13:22
Are active charcoal air filters effective against finishing fumes?
Awarded Mar 5, 2018 at 18:24
Should I build basement shelving so it's square with the wall or with the floor?
Awarded Jan 16, 2018 at 15:25
Can you hook up two shop-vacs in parallel to increase airflow through a dust collection system?
Awarded Jan 12, 2018 at 15:44
How do I achieve a "piano black" high gloss finish on wood?
Awarded Jan 1, 2018 at 13:11
Not-so-obvious disadvantages of butt joints
Awarded Dec 19, 2017 at 15:08
Why are keyed drill chucks still available for modern tools?
Awarded Nov 10, 2017 at 17:48
How do you use a 300 & 600 grit diamond jointer / planer blade sharpener / knife hone holder?
Awarded Sep 29, 2017 at 21:21
What is the difference between flush trim, pattern, and template router bits?
Awarded Aug 29, 2017 at 15:14
5000rpm vs 5500rpm circular saw
Awarded May 26, 2017 at 16:32
In what situations would I use a belt sander versus a random orbit sander?
Awarded May 25, 2017 at 22:07
How and when should I sharpen my router bits?
Awarded May 2, 2017 at 14:08
I was thinking of buying a router. I tried a router bit in my power drill. It didn't work
Awarded Mar 25, 2017 at 21:38
1
2 3